Project ScratchDuinoRobotKit blackline

Latest revision as of 19:46, 27 June 2018

[edit] Name of author (s)

[edit] Description of the ROBBO Scratch project

Trip time	Sketch	Power supply	ROBBO Scratch	Trip time	Arduino IDE
Algorithm 1. The robot uses ONE numerical value of the line sensor — the AVERAGE of two extreme values, obtained when the sensor is positioned above the white area and above the black line. If the sensor shows a value greater than the average, then the robot turns to the left during 0.1 second and goes forward during 0.1 second. If the sensor shows a value less than the average, then the robot turns to the right during 0.1 second and goes forward during 0.1 second. The trajectory the robot follows is a zigzag.
38 seconds		USB	ROBBO Scratch Video Download the sketch	30 seconds	To turn the robot on and off, two touch sensors are used: analogRead(A3) – right-hand rear sensor — ON, analogRead(A1) — left-hand rear sensor — OFF Download the sketch
13 seconds	The high speed causes numerous errors. At a high speed, the robot misses the turns in half the cases.	Battery 7.4V	ROBBO Scratch Video Download the sketch	11 seconds	Arduino IDE Video Download the sketch
Algorithm 2. The robot uses SEVEN (FIVE, in case of USB) numerical values of the line sensor — these are values between two extreme values, obtained when the sensor is positioned above the white area and above the black line. The readings of the line sensor are as follows: » 0 means the position above the white area. Both motors are on and in full swing (255), the left-hand motor is rotating forward, the right-hand motor is rotating backward. The robot turns in place during 0.1 second. » 1 means the position above the white area, closer to the black line. The left-hand motor is on and in full swing (255), rotating forward, while the right-hand motor is off. The robot turns on the fly during 0.1 second. » 2 means the position at the border of the white and black areas, even more closer to the black line. The left-hand motor is on and in full swing (255), rotating forward, while the right-hand motor is at its half power (120), rotating forward, too. The robot goes ahead and turns a bit, on the fly, during 0.1 second. » 3 means the position at the border of the white and black areas, already above the black line. The left-hand and the right-hand motors are on and in full swing (255), both rotating forward. The robot goes ahead during 0.1 second. » The rest of the values (4, 5, and 6) are mirroring the 0, 1, and 2 options, respectively. The trajectory the robot follows is a smooth curve with long tangent sections, so the robot can travel all along without slowing down.
25–26 seconds	ROBBO Scratch handles the timing data with worse quality than Arduino IDE, therefore we have reduced the number of the ranges to 5 and simplified the action of motors. The motors are rotating forward all the time, with varying power.	USB	Download the sketch	18 seconds	Arduino IDE Video Download the sketch
12 seconds	At a high speed, the robot misses the turn in 4 of 5 cases.	Battery 7.4V	It is important to modify the sketch coded for USB, because at a high speed, the intermediate values of the sensor cannot be handled. We join all the intermediate values. Download the sketch	9.5 seconds	It is important to immediately modify the sketch, coded for a 5V power supply (USB). Replace the robot's turning time of 0.1 seconds by 0.01 seconds. And increase the time of going ahead up to 0.2 seconds. It is necessary because at a high speed, the robot rushes too fast along the path section where the values of the sensors are changing.
Algorithm 3. The robot uses EIGHT numerical values of the line sensor — these are values between two extreme values, obtained when the sensor is positioned above the white area and above the black line. The trajectory the robot follows is a line with long straight sections, and the robot can travel all along without slowing down.
XX seconds
XX seconds				8.5 seconds (track record!)	Arduino IDE Video Download the sketch

[edit] Description of travelling along the black line with TWO sensors

It is impossible to travel along a complicated track with crossings, forks, "zebras", and inverted sections using only one sensor.
When two sensors are used, special algorithms are needed to automate the robot's motion.

XX seconds XX seconds XX seconds XX seconds

Trip time	Sketch	Power supply	ROBBO Scratch	Trip time	Arduino IDE
Algorithm 4. Relay controller. This algorithm is intended to keep the robot in the position "Both sensors of the robot are above the white area", that is, to the left and to the right from the black line. If both sensors are above the black line, the robot stops.
XX seconds		USB	When powered by USB, the robot stops at the turn, because both sensors get above the black line. Download the sketch	XX seconds	analog0 = analogRead(A0); // Got a value from the sensor analog1 analog4 = analogRead(A4); // Got a value from the sensor analog4 limit = 50; time1 = 200; power = 255; //if both sensors "see" white, the robot moves straight: if (analog0 < limit && analog4 < limit) { move_robbo (power, power, 0, 0, time1); } //if the left sensor "sees" black, the robot turns to the left: if (analog0 > limit && analog4 < limit) { move_robbo (0, power, 0, 0, time1); } //if the right sensor "sees" black, the robot turns to the right: if (analog0 < limit && analog4 > limit) { move_robbo (power, 0, 0, 0, time1); }
10 seconds		7.4V	When extra powered from the battery, the robot misses the sharp turns, because at a speed, the sensors cannot be above the black line both at the same time. ROBBO Scratch Video Download the sketch	XX seconds	[1] Arduino IDE Video]. If the battery charge is low, the robot stops at the turn. Download the sketch - sensor readings Download the sketch - relay controller + ON/OFF by touch sensors
Algorithm 5. Proportional controller. Proportional controller is a device whose controlling action over an object depends on the object's deflection from a certain state. Such deflection is called error and we denote it with a letter E. In our case, the error is the difference between the readings of two line sensors: E = S1 – S2. To obtain the value of controlling action U, we multiply the E value by a chosen factor kp: U = kp⋅E. U is the momentum that we have to add to one motor and extract from other motor. Thus, the robot will control its position itself — that is, for turning or taxing to the required direction.
	USB	ROBBO Scratch Video
XX seconds		Download the sketch
	7.4V	[ROBBO Scratch Video Download the sketch]	XX seconds	[Arduino IDE Video Download the sketch]
Algorithm 6. Proportional-plus-differential controller.
	USB
	7.4V	[ROBBO Scratch Video Download the sketch]	XX seconds	[Arduino IDE Video Download the sketch]
Algorithm 7. Proportional-integral-differential controller.
XX seconds		USB
XX seconds		Battery 7.4V	[ROBBO Scratch Video Download the sketch]	XX seconds	[Arduino IDE Video Download the sketch]

@@ Line 2: / Line 2: @@
 [[User:Elena Vostrikova]]
-==Category party==
+==Description of the ROBBO Scratch project ==
-Party outside the category
-==Nomination serving festival project==
+[https://yadi.sk/d/GbsoeO923YVCda тест датчиков]
-ScratchDuinoPobotKit
-==Description of the project ROBBO Scratch==
+[https://yadi.sk/d/H8jsL67k3YVDX9 тест датчиков. Файл INO]
 {| class="standard" border=1
@@ Line 12: / Line 12: @@
 |--
-!Время заезда ||Количество ошибок||Источник питания||ROBBO Scratch||Время заезда|| Arduino IDE
+!Trip time ||Sketch||Power supply||ROBBO Scratch||Trip time|| Arduino IDE
 |--
 |-
-|colspan=6| <center>'''<font color="red">Алгоритм 1. </font>''' Робот использует '''ОДНО''' числовое значение датчика линии - СРЕДНЕЕ арифметическое между  <br> двумя крайними значениями, полученными при положении датчика над белым полем  и черной линией.  <br> Если датчик показывает значение больше этого числа, то робот 0,1 сек. <br>  поворачивается налево и 0.1 сек. едет прямо.  <br>  Если датчик показывает значение меньше среднего арифметического,  <br> то робот 0,1 сек. поворачивается направо и 0.1 сек. едет прямо. <br>  Траектория движения робота напоминает движение по зигзагу <br>  [[File:Zigzag.png]] <br></center>
+|colspan=6| <center>'''<font color="red">Algorithm 1.</font>''' The robot uses '''ONE''' numerical value of the line sensor — the AVERAGE of <br>two extreme values, obtained when the sensor is positioned above the white area and above the black line.  <br> If the sensor shows a value greater than the average, then the robot turns to the left during 0.1 second <br>and goes forward during 0.1 second. <br>If the sensor shows a value less than the average,  <br> then the robot turns to the right during 0.1 second and goes forward during 0.1 second. <br>The trajectory the robot follows is a zigzag. <br><br>[[File:Zigzag.png]] <br></center>
 |-
-|38 секунд.
+|38 seconds
-||небольшое
+||[[File:Black line analog1 code1.png]]
 ||USB
-||[https://youtu.be/Mvm1UxDkF-A Видео ROBBO Scratch] <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Project_Black_line_analog1_code1.sb2 Cсылка на скачивание скетча] [[File:Black line analog1 code1.png]]
+||[https://youtu.be/Mvm1UxDkF-A ROBBO Scratch Video] <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Project_Black_line_analog1_code1.sb2 Download the sketch]
-||30  секунд.
+||30  seconds
-||Для включения и выключения робота  <br> используются два датчика касания: analogRead(A3) <br>  - задний правый - включение, analogRead(A1)- <br>  задний левый  - выключение,   <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black_line_analog1_zigzag.ino Cсылка на скачивание скетча]
+||To turn the robot on and off, two touch sensors are used: <br>analogRead(A3) – right-hand rear sensor — ON, <br> analogRead(A1) — left-hand rear sensor — OFF <br> [https://yadi.sk/d/h7YJVH2a3YRS5d Download the sketch]
 |--
-|13 секунд.
+|13 seconds
-||большое. <br>На высокой скорости <br>робот в половине случаев <br>проскакивает поворот.
+||The high speed causes numerous errors. <br>At a high speed, the robot misses the turns in half the cases.
-||Батарейка 7,4 В
+||Battery 7.4V
-||[https://youtu.be/0X8lQPaMAsU Видео ROBBO Scratch] <br>[http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Project_Black_line_analog1_code1.sb2 Cсылка на скачивание скетча]
+||[https://youtu.be/0X8lQPaMAsU ROBBO Scratch Video] <br>[http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Project_Black_line_analog1_code1.sb2 Download the sketch]
-||11 секунд.
+||11 seconds
-||[https://youtu.be/1VJxK9uEw7A Видео Arduino IDE] <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black_line_analog1_zigzag.ino  Cсылка на скачивание скетча]
+||[https://youtu.be/1VJxK9uEw7A Arduino IDE Video] <br>[http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black_line_analog1_zigzag.ino Download the sketch]
 |-
-|colspan=6| <center>'''<font color="red">Алгоритм № 2 </font>''' Робот использует '''СЕМЬ (ПЯТЬ для USB)''' числовых значений датчика линии - промежуточные значения  между  <br> двумя крайними значениями, полученными при положении датчика над белым полем  и черной линией.  <br> Если датчик показывает значение: <br> '''0''', то это означает положение над белым полем. Оба мотора включены на полную мощность (255), левый  мотор крутится вперед, а правый -назад. Робот поворачивается на месте 0,1 секунды <br> '''1''', то это означает положение над белым полем, ближе к чёрной линии. Левый  мотор включен на полную мощность (255) и крутится вперед, а правый  мотор стоит. Робот поворачивается в движении 0,1 секунды <br> '''2''', то это означает положение на границе белого и черного полей, еще ближе к чёрной линии. Левый  мотор включен на полную мощность (255) и крутится вперед, а правый  включен на половине  мощности (120) и тоже крутится вперед. Робот едет прямо и немного поворачивается в движении в течение 0,1 секунды <br> '''3''', то это означает положение на границе белого и черного полей, уже на  чёрной линии. Левый  и правые моторы включены на полную мощность (255) и оба крутятся вперед. Робот едет прямо в течение 0,1 секунды <br> Остальные значения (4,5 и 6) являются зеркальными по отношению к 0,1 и 2. <br> Траектория движения робота напоминает плавную линию с длинными прямыми участками, на всём протяжении которой робот едет, не притормаживая <br> [[File:Line.png]]<br></center>
+|colspan=6| <center>'''<font color="red">Algorithm 2.</font>''' The robot uses '''SEVEN (FIVE, in case of USB)''' numerical values of the line sensor — these are values between <br> two extreme values, obtained when the sensor is positioned above the white area and above the black line. <br><br>The readings of the line sensor are as follows: </center>'''» 0''' means the position above the white area. Both motors are on and in full swing (255), the left-hand motor is rotating forward, the right-hand motor is rotating backward. The robot turns in place during 0.1 second. <br>'''» 1''' means the position above the white area, closer to the black line. The left-hand motor is on and in full swing (255), rotating forward, while the right-hand motor is off. The robot turns on the fly during 0.1 second. <br>'''» 2''' means the position at the border of the white and black areas, even more closer to the black line. The left-hand motor is on and in full swing (255), rotating forward, while the right-hand motor is at its half power (120), rotating forward, too. The robot goes ahead and turns a bit, on the fly, during 0.1 second. <br>'''» 3''' means the position at the border of the white and black areas, already above the black line. The left-hand and the right-hand motors are on and in full swing (255), both rotating forward. The robot goes ahead during 0.1 second. <br>'''»''' The rest of the values ('''4''', '''5''', and '''6''') are mirroring the '''0''', '''1''', and '''2''' options, respectively. <center><br> The trajectory the robot follows is a smooth curve with long tangent sections, so the robot can travel all along without slowing down.<br><br> [[File:Line.png]]<br></center>
 |-
-|25-26 секунд
+|25–26 seconds
-||небольшое
+|ROBBO Scratch handles the timing data with worse quality than Arduino IDE, therefore we have reduced the number of the ranges to 5 and simplified the action of motors.<br> The motors are rotating forward all the time, with varying power.
-||USB. ROBBO Scratch хуже, чем ArduiniIDE <br> обрабатывает время движения, поэтому <br> количество диапазонов мы сократили до 5 <br> и упростили движение моторов.<br>  Они все время двигаются вперед с<br>  разной мощностью
+||USB
-||[http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black-Line-USB-analog1-RSalgoritm2.sb2 Cсылка на скачивание скетча]
+|| [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black-Line-USB-analog1-RSalgoritm2.sb2 Download the sketch]
-|| 18 секунд.
+|| 18 seconds
-||[https://youtu.be/yjE4zHcG3h4 Видео Arduino IDE] <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black_line_analog1_Speed.ino |Cсылка на скачивание скетча]
+||[https://youtu.be/yjE4zHcG3h4 Arduino IDE Video] <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black_line_analog1_Speed.ino Download the sketch]
 |--
-|12 секунд
+|12 seconds
-||большое. <br>На высокой скорости <br>робот в 4 из 5 случаев <br>проскакивает поворот.
+||<br>At a high speed, the robot misses the turn in 4 of 5 cases.
-||Батарейка 7,4 В
+||Battery 7.4V
-||В скетч, разработанный для USB, необходимо <br>внести изменения, т.к. на большой <br>скорости промежуточные значения датчика <br>не обрабатываются. Объединяем все<br>  промежуточные значения <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black-Line-USB-analog1-RSalgoritm2.sb2 Cсылка на скачивание скетча]
+||It is important to modify the sketch coded for USB, because at a high speed, the intermediate values of the sensor cannot be handled. <br>We join all the intermediate values. <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black-Line-USB-analog1-RSalgoritm2.sb2 Download the sketch]
-||9,5 секунд.
+||9.5 seconds
-||Скетч, написанный для питания 5В (USB) <br> сразу важно изменить. Заменить <br>время движения робота в поворотах со 100 до <br>10 милисекунд. А время движения прямо<br> увеличить до  200 мили секунд. <br> Эти изменения необходимы, т.к. на большой<br> скорости робот слишком быстро проезжает <br>участок, где изменяются значения датчиков<br> Cсылка на скачивание скетча.
+||It is important to immediately modify the sketch, coded for a 5V power supply (USB). <br>Replace the robot's turning time of 0.1 seconds by 0.01 seconds. And increase the time of going ahead up to 0.2 seconds. <br>It is necessary because at a high speed, the robot rushes too fast along the path section where the values of the sensors are changing.<br>
 |-
-|colspan=6| <center>'''<font color="red">Алгоритм № 3 </font>''' Робот использует '''ВОСЕМЬ''' числовых значений датчика линии - промежуточные значения  между  <br> двумя крайними значениями, полученными при положении датчика над белым полем  и черной линией. <br> Траектория движения робота напоминает прямую линию с длинными прямыми участками, на всём протяжении которой робот едет, не притормаживая <br> [[File:Line-line.png]]<br></center>
+|colspan=6| <center>'''<font color="red">Algorithm 3.</font>''' The robot uses '''EIGHT''' numerical values of the line sensor — these are values between
+two extreme values, obtained when the sensor <br>is positioned above the white area and above the black line. <br>The trajectory the robot follows is a  line with long straight sections, and the robot can travel all along without slowing down.<br><br> [[File:Line-line.png]]<br></center>
 |-
-|хх секунд
+|XX seconds
 ||
 ||
@@ Line 57: / Line 58: @@
 ||
 |--
-|хх секунд
+|XX seconds
 ||
 ||
 ||
-|| <font color="red">8.5 секунд (рекорд трассы!)</font>
+|| <font color="red">8.5 seconds (track record!)</font>
-||  [https://youtu.be/GO4fXPLDF1k Видео Arduino IDE] <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black_line_analog1_Speed-7-4-var2.ino Cсылка на скачивание скетча]
+||  [https://youtu.be/GO4fXPLDF1k Arduino IDE Video] <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black_line_analog1_Speed-7-4-var2.ino Download the sketch]
+|}
+==Description of travelling along the black line with TWO sensors==
+<center>It is impossible to travel along a complicated track with crossings, forks, "zebras", and inverted sections using only one sensor. <br>When two sensors are used, special algorithms are needed to automate the robot's motion.
+</center>
+{| class="standard" border=1
+|--
+!Trip time ||Sketch||Power supply||ROBBO Scratch||Trip time || Arduino IDE
+|--
+|-
+|colspan=6| <center>'''<font color="red">Algorithm 4.</font> Relay controller.''' This algorithm is intended to keep the robot in the position "Both sensors of the robot are above the white area", <br>that is, to the left and to the right from the black line. If both sensors are above the black line, the robot stops.<br> [[File:2line.png]] </center>
+|-
+|XX seconds
+||[[File:Eng-relay-controller-RS.png]]
+||USB
+||When powered by USB, the robot stops at the turn, because both sensors get above the black line. [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black-Line-USB-analog2_and_analog5-RS.sb2 Download the sketch]
+||XX seconds
+||
+<blockquote>
+    analog0 = analogRead(A0); // Got a value from the sensor analog1<br>
+    analog4 = analogRead(A4); // Got a value from the sensor analog4<br>
+    limit = 50;<br>
+    time1 = 200;<br>
+    power = 255;<br>
+<br>
+    //if both sensors "see" white, the robot moves straight:<br>
+    if (analog0 < limit && analog4 < limit) {<br>
+      move_robbo (power, power, 0, 0, time1);<br>
+    }<br>
+    //if the left sensor "sees" black, the robot turns to the left:<br>
+    if (analog0 > limit && analog4 < limit) {<br>
+      move_robbo (0, power, 0, 0, time1);<br>
+    }<br>
+    //if the right sensor "sees" black, the robot turns to the right:<br>
+    if (analog0 < limit && analog4 > limit) {<br>
+      move_robbo (power, 0, 0, 0, time1);<br>
+    }<br>
+</blockquote>
+|--
+|'''10 seconds'''
+||
+||7.4V
+|| When extra powered from the battery, the robot misses the sharp turns, because at a speed, the sensors cannot be above the black line both at the same time. [https://youtu.be/9rBbZvaQ1FE ROBBO Scratch Video] <br>[http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Black-Line-USB-analog2_and_analog5-RS.sb2 Download the sketch]
+||XX seconds
+||[https://youtu.be/Dv97KMJkuF0] Arduino IDE Video]. If the battery charge is low, the robot stops at the turn. <br>[http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Test_analog0-analog4.ino Download the sketch - sensor readings] <br> [http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Relay-controller-2-5.ino Download the sketch - relay controller + ON/OFF by touch sensors]
+|-
+|colspan=6| <center>'''<font color="red">Algorithm 5.</font> Proportional controller.''' Proportional controller is a device whose controlling action over an object depends on the object's deflection from a certain state. <br>Such deflection is called '''error''' and we denote it with a letter E. In our case, the error is the difference between the readings of two line sensors: E = S1 – S2. <br>To obtain the value of controlling action '''U''', we multiply the E value by a chosen factor '''kp''': U = kp⋅E. U is the momentum that we have to '''add''' to one motor and '''extract''' from other motor. <br>Thus, the robot will control its position '''itself''' — that is, for turning or taxing to the required direction.<br>
+|-
+XX seconds
+||
+||USB
+||ROBBO Scratch Video <br>
+|-
+|XX seconds
+||
+||[http://wiki.robbo.ru/wiki/%D0%A4%D0%B0%D0%B9%D0%BB:Relay_scratchduino.ino Download the sketch]
+|-
+XX seconds
+||
+||7.4V
+||[ROBBO Scratch Video <br>Download the sketch]
+||XX seconds
+||[Arduino IDE Video <br>Download the sketch]
+|-
+|colspan=6| '''<font color="red">Algorithm 6.</font> Proportional-plus-differential controller.''' </center>
+|-
+XX seconds
+||
+||USB
+||
+||
+||
+|--
+XX seconds
+||
+||7.4V
+||[ROBBO Scratch Video <br>Download the sketch]
+|XX seconds
+||[Arduino IDE Video <br>Download the sketch]
+|-
+|colspan=6| <center>'''<font color="red">Algorithm 7.</font> Proportional-integral-differential controller.'''<br> </center>
+|-
+|XX seconds
+||
+||USB
+||
+||
+||
+|--
+|XX seconds
+||
+||Battery 7.4V
+||[ROBBO Scratch Video <br>Download the sketch]
+||XX seconds
+||[Arduino IDE Video <br>Download the sketch]
 |}
-[[Category:Projects]]
-[[Category:Projects_ROBBOKit]]

Project ScratchDuinoRobotKit blackline

Latest revision as of 19:46, 27 June 2018

[edit] Name of author (s)

[edit] Description of the ROBBO Scratch project

[edit] Description of travelling along the black line with TWO sensors

Personal tools

Namespaces

Variants

Views

Actions

Search

Navigation

Tools

Print/export