Project ScratchDuinoRobotKit blackline

Revision as of 15:08, 25 June 2018

Name of author (s)

Description of the ROBBO Scratch project

Trip time	Sketch	Power supply	ROBBO Scratch	Trip time	Arduino IDE
Algorithm 1. The robot uses ONE numerical value of the line sensor — the AVERAGE between two extreme values, obtained when the sensor is positioned above the white area and above the black line. If the sensor shows a value greater than the average, then the robot turns to the left during 0.1 second and goes forward during 0.1 second. If the sensor shows a value less than the average, then the robot turns to the right during 0.1 second and goes forward during 0.1 second. The trajectory the robot follows is a zigzag.
38 seconds		USB	ROBBO Scratch Video Download the sketch	30 seconds	To turn the robot on and off, two touch sensors are used: analogRead(A3) – right-hand rear sensor — ON, analogRead(A1) — left-hand rear sensor — OFF Download the sketch
13 seconds	The high speed causes numerous errors. At a high speed, the robot cuts off the corners in half the cases.	Battery 7.4V	ROBBO Scratch Video Download the sketch	11 seconds	Arduino IDE Video Download the sketch
Algorithm 2 The robot uses SEVEN (FIVE, in case of USB) numerical values of the line sensor — these are values between two extreme values, obtained when the sensor is positioned above the white area and above the black line. The readings of the sensor are as follows: » 0 means the position above the white area. Both motors are on and in full swing (255), the left-hand motor is rotating forward, the right-hand motor is rotating backward. The robot turns in place during 0.1 second. » 1 means the position above the white area, closer to the black line. The left-hand motor is on and in full swing (255), rotating forward, while the right-hand motor is off. The robot turns on the fly during 0.1 second. » 2 means the position at the border of the white and black areas, even more closer to the black line. The left-hand motor is on and in full swing (255), rotating forward, while the right-hand motor is at its half (120), rotating forward, too. The robot goes ahead and turns a bit, on the fly, during 0.1 second. » 3 means the position at the border of the white and black areas, already above the black line. The left-hand and the right-hand motors are on and in full swing (255), both rotating forward. The robot goes ahead during 0.1 second. » The rest of the values (4, 5, and 6) are mirroring the 0, 1, and 2 options, respectively. The trajectory the robot follows is a smooth curve with long tangent sections, so the robot can travel all along without slowing down.
25–26 seconds	ROBBO Scratch хуже, чем Arduino IDE обрабатывает время движения, поэтому количество диапазонов мы сократили до 5 и упростили движение моторов. Они все время двигаются вперед с разной мощностью	USB	Download the sketch	18 seconds	Arduino IDE Video Download the sketch
12 seconds	At a high speed, the robot проскакивает поворот in 4 of 5 cases.	Battery 7.4 V	It is important to modify the sketch coded for USB, because at a high speed, the in-between values of the sensor cannot be handled. Объединяем все промежуточные значения Download the sketch	9.5 seconds	It is important to immediately modify the sketch, coded for a 5V power supply (USB). Заменить время движения робота в поворотах со 100 до 10 milliseconds. А время движения прямо увеличить до 200 milliseconds. It is necessary because at a high speed, the robot rushes too fast along the path section, where the values of the sensors are changing
Algorithm 3 The robot uses EIGHT numerical values of the line sensor — these are values between two extreme values, obtained when the sensor is positioned above the white area and above the black line. The trajectory the robot follows is a line with long straight sections, and the robot can travel without slowing down all along.
XX seconds
XX seconds				8.5 seconds (рекорд трассы!)	Arduino IDE Video Download the sketch

Описание проезда по чёрной линии с ДВУМЯ датчиками

Сложную трассу с перекрестками, ответвлениями, "зебрами" и инверсными участками с одним датчиком проехать невозможно. При подключении двух датчиков требуется использовани специальных алгоритмов, которые автоматизируют движение робота.

XX seconds XX seconds XX seconds

Trip time	Sketch	Power supply	ROBBO Scratch	Trip time	Arduino IDE
Algorithm 4. - Релейный регулятор Задача этого алгоритма - удерживать робота в положении "Оба датчика робота находятся над белой линией", т.е. слева и справа от чёрной линии. Если оба датчика попадают на черную линию, the robot останавливается
XX seconds		USB	При питании от USB робот останавливается на повороте, т.к. оба датчика оказываются на черной линии Download the sketch	XX seconds	analog0 = analogRead(A0); // Got a value from the sensor analog1 analog4 = analogRead(A4); // Got a value from the sensor analog4 limit = 50; time1 = 200; power = 255; //if both sensors "see" white, the robot moves straight: if (analog0 < limit && analog4 < limit) { move_robbo (power, power, 0, 0, time1); } //if the left sensor "sees" black, the robot turns to the left: if (analog0 > limit && analog4 < limit) { move_robbo (0, power, 0, 0, time1); } //if the right sensor "sees" black, the robot turns to the right: if (analog0 < limit && analog4 > limit) { move_robbo (power, 0, 0, 0, time1); }
10 seconds		7.4 V	When extra powered from the battery, the robot cuts the sharp turning off, because at a speed, the sensors cannot be above the black line both at the same time ROBBO Scratch Video Download the sketch	XX seconds	Arduino IDE Video. If the battery is run down, the robot stops at the turn. Download the sketch - sensor readings Download the sketch - простой релейный регулятор + ON/OFF by touch sensors
Algorithm 5 Пропорциональный регулятор Пропорциональный̆ регулятор is a device that оказывающее управляющее воздействие на объект пропорционально его отклонению от заданного состояния. Принцип действия П-регулятора основывается на том, что мы находим значение отклонения от заданного состояния, которое назовем error и обозначим буквой E. Ошибка – это разница между показаниями датчиков линии: E = S1 – S2. To obtain the value of controlling action U, we multiply this value by a chosen ratio kp: U = kp⋅E. U is the momentum that we have to add to one motor and extract from other motor. Thus, the robot will control its position itself — that is, for turning or taxing to the required direction.
XX seconds.		USB	ROBBO Scratch Video	XX seconds	Download the sketch
	7.4 V	ROBBO Scratch Video Download the sketch	XX seconds	Arduino IDE Video Download the sketch
<center>Algorithm 6 Пропорционально-дифференциальный регулятор
	USB
	7.4 V	ROBBO Scratch Video Download the sketch	XX seconds	Arduino IDE Video Download the sketch
Algorithm 7 ПИД-регулятор
XX seconds		USB
XX seconds		Battery 7.4 V	ROBBO Scratch Video Download the sketch	XX seconds	Arduino IDE Video Download the sketch

@@ Line 45: / Line 45: @@
 |-
 |colspan=6| <center>'''<font color="red">Algorithm 3 </font>''' The robot uses '''EIGHT''' numerical values of the line sensor — these are values between
-two extreme values, obtained when the sensor is positioned above the white area and above the black line. <br> The trajectory the robot follows is a  line with long straight sections, and the robot can travel without slowing down all along. <br> [[File:Line-line.png]]<br></center>
+two extreme values, obtained when the sensor <br>is positioned above the white area and above the black line. <br> The trajectory the robot follows is a  line with long straight sections, and the robot can travel without slowing down all along. <br> [[File:Line-line.png]]<br></center>
 |-
 |XX seconds

Project ScratchDuinoRobotKit blackline

Revision as of 15:08, 25 June 2018

Name of author (s)

Description of the ROBBO Scratch project

Описание проезда по чёрной линии с ДВУМЯ датчиками

Personal tools

Namespaces

Variants

Views

Actions

Search

Navigation

Tools

Print/export